Rings for spinning rods - replacement and placement of rings

Rings: highlights

The pass ring is characterized by lightness, strength and durability.

Consists of the following parts:

Frame.
Insert.

These elements are made using durable, corrosion-resistant material that is lightweight, because the weight of the rings affects the performance of the spinning rod.

The frame characteristics assume the following parameters:

Diameter.
Total length.
Number of legs.
Overall height.

Inserts are made of ceramics and metal-ceramics.

There are 4 types of rings:

Throughput – SIC. Has a silicon carbide insert. They are wear resistant. Using the part, the braided thread is fixed to the base of the tackle.
Pass – SIH. Lightweight ring made of durable material. Designed to hold maximum weight.
Passage detail LOW. Specialized part. Necessary to prevent the line from overlapping during casting.
Passage part with ceramic insert. Designed for fixing a cord made of monofilament material.

A special design feature is the tulip ring located at the tip of the form.

Building a tulip:

The frame is welded to the pointed part.
This part is fixed at the top of the tackle.

Attention! The adhesive for attaching the ring parts must be of high quality.

Requirements for rings:

Polished surface without cracks or chips.
No roughness.
Solid and clean base.
Firm fit.

When choosing, you must pay attention to the following characteristics:

Size.
Weight.
Diameter.

The number of rings ensures the distribution of the mass of the whip component over the entire distance of the rod. This affects the catch of fish. A smaller amount affects the cast, the range of which increases. This increases the likelihood of failure.

In order to ensure the safety of the spinning rod, it is necessary to correctly arrange the rings:

Their number depends on the length of the rod: pound-1 (this means that with a length of 7 pounds, or 213 centimeters, the number of rings will be 6 pieces, with a length of 9 pounds - 8 pieces).
The distance between the elements towards the top of the rod increases by 0.2 millimeters.

Passage rings for spinning rods: how to remove, change and attach them to the spinning rod with your own hands

Spinning rings are an important element that is equipped on almost all modern fishing rods. its function is to maintain the balance of the tackle and create a pass for the fishing line. These elements simplify the use of the fishing rod, prevent the line from sagging and tangling, and increase the casting distance of the tackle. But, despite all their advantages, they sometimes break. We invite fishing enthusiasts to get acquainted with the characteristics of this part, the features of installation and replacement of guide rings.

Characteristics of fishing rod rings

Good rings for spinning rods should be resistant to adverse environmental conditions (high humidity, dirt, mechanical factors), combine high strength and lightness.

These elements, regardless of their type and size, consist of 2 parts:

Most manufacturers create rings from resistant materials that resist corrosion well and have a low specific gravity.

If we talk about the characteristics of the ring frame, then these include the following parameters:

length;
diameter;
height;
number of legs.

The inserts that are included in all the rings on the spinning rod are made of metal-ceramics or ceramics.

A special feature of spinning fishing rods is the presence of the smallest ring at the top, called a “tulip”. It consists of a piece with a sharp end, which is connected to the frame by welding, and then fixed to the top of the fishing tackle.

Passage rings intended for spinning rods must meet the following requirements:

well polished, smooth surface without chips or cracks;
solid base with a good margin of safety;
absence of roughness and unevenness on the surface.

If this is your first time choosing rings for your spinning rod, pay attention to their diameter, weight and size.

The success of fishing depends on the number of rings on the rod. These elements affect the uniform distribution of the load along the entire length of the gear. For example, with a smaller number of them, the casting range of a fishing line with bait increases, but the risk of breaking the form (“stick” on which the reel, fishing line and other fishing equipment is attached) increases.

Replacing the ring on a spinning rod

Breakage of the ring on a spinning rod is a common problem that experienced and novice fishermen have had to deal with. In such a situation, the question becomes relevant: how to replace the ring on a spinning rod and is it always necessary to resort to this procedure?

Replacement of the element is necessary in the following cases:

if the tip of the spinning rod is broken;
if, after prolonged use, cuts from the fishing line appear on the frames;
the frame is deformed;
The leg connecting the ring and the insert broke.

If a defect (chip, crack) appears on the pass element, you can replace it yourself by preparing the necessary tools. Follow these simple instructions to change the ring on your fishing rod yourself.

What tools and materials will be needed?

To replace the ring on a fishing rod with your own hands, prepare a set of tools and materials from the following list.

New access element. You can find a new fishing rod ring at any fishing store. Such products are presented in a large assortment. We recommend giving preference to products with ceramic inserts.
Synthetic fishing line and thread made of the same material (without lint).
A large cardboard box that will serve as a stand for the spinning rod. In the side parts of the box, located parallel to each other, it is necessary to make triangular grooves for fishing gear.
Parquet varnish with a polyurethane base, which covers the winding part of the structure.
Hair dryer.
Wire of small thickness.
A lighter or candle with a burning wick.
Magnifier.
Epoxy adhesive.
Sharp knife.
Silicone tube.
Masking tape or electrical tape.
Bowl for mixing epoxy glue.
A brush with which the adhesive composition is evenly distributed over the surface of the pass ring.

To make the turns of the sealing synthetic thread (or monofilament line) more dense, use a small and strong twig. Instead, you can take a popsicle stick or from a counting set.

Correct placement of rings

Attaching guide rings to a fishing rod has its own characteristics. According to the rules, these elements are placed along the line of the inner seam on the whip.

You can install them on the rod in the following ways:

Traditional. You need to take several ring elements and use them to create a cone-shaped tunnel for the fishing line. The largest ring is located at the base, near the coil, and the element with the smallest diameter is at the top of the structure.
New. The part at the base is moved closer to the center of the structure, reducing the length of the cone. Then the main part of the fishing line is passed through small rings.

The rings can be placed on the rod in 3 positions:

Below or above in relation to the whip. This spinning rod assembly is ideal and has the greatest rigidity.
From the side, at an angle of 90 °C (left or right). This placement indicates the installation of pass elements along the soft line of the whip. This may indicate poor quality assembly or that the tackle is designed for slow action.
A chaotic arrangement of ring elements on a fishing rod is considered incorrect. With such an arrangement, the fisherman will not be able to cast the tackle over a long distance without making mistakes. The twisting forces at the time of landing the fish will deform the rod, and after 1-1.5 months of active fishing the tackle will break.

If you have the desire and free time, you can make a spinning ring with your own hands.

To do this, prepare:

hard insert;
electric drill;
paste.

It is necessary to attach the insert using paste at the base of the frame. Using an electric drill, you should polish the surface to make the fixation as stable as possible. To complete the work, secure the ring to the whip.

Installation and replacement

The throughput element is removed mainly as a result of a defect. For example, if the frame is cracked or a defect is found on the insert.

In order to make the replacement, the following tools are needed:

New part.
Sharp blade.
Instantly hardening adhesive base.
A set of epoxy-based paste (double dose of Bolon, paste with a fixing effect).
A cord made of nylon material or a braided thread (the diameter should be minimal).
Cup for mixing epoxy glue.
Rod.
A brush will help to evenly distribute the epoxy paste.

Installation

Heat the section of the rod that is intended for wrapping the ring element (you can use a hairdryer). This will help make the area softer. If the warm-up cools down quickly, it is possible to repeat this method again during operation. The absence of softening means that a different product has been applied to the hard coating, which differs in composition from the epoxy base. In this regard, heating attempts should be excluded, as they will not be successful.
Using the tip of a knife, make an incision on the surface of the tab of the ring element. This will prevent damage to the shape. At this stage it is necessary to remove the coating completely. If you cannot remove the entire winding with one cut, it is worth repeating the steps to achieve an optimal result.
In order to get rid of all particles, you can use a wooden or plastic base. These elements will help remove all the winding without damaging the surface.
Sharpen the edges of the handle. This will make it easier to wind the cord.
When choosing a thread, you should focus on a synthetic base, the thickness of which is No. 50 according to the sewing nomenclature.
The winding process itself consists of 2 stages: tensioning the cord and fixing it on the form. For convenience, you should use a thick cardboard box.
Next, you need to pass the cord through a thick covering, such as a stack of paper. This will allow you to achieve the most optimal tension. To prevent the spool of thread from unwinding prematurely, you should lower it into a container.
The cord is fixed by turning the element around the form. To do this, you need to overlap, which is the most reliable way. Secure the winding section with a piece of tape.
This process must be repeated until the thread reaches the top.
Place the monofilament line behind the cord before the line reaches the end approximately 4 millimeters.
When the winding is complete, secure the cord and cut off the end.
Thread the thread through the loop and secure it.
Trim the excess cord and tighten the element so that unwinding is prevented.

Replacing the tulip

The process of replacing a tulip is easy to use and takes place in several stages:

Apply masking tape to the edge of the tulip. This will help the glue not to go beyond the boundaries of the planting of this element at the end of the process.
The decorative winding is removed. In this case, the area should be cut as carefully as possible so as not to damage the foot. It is also necessary to control the heating process to prevent fire.
After the winding is removed, you need to heat the tulip and remove it. You can use a lighter for this.
If low-quality glue is used, you will have to cut off the tulip along with the top section.
Clean the tackle from paste particles.
If the coating has been removed along with the glue, apply a small layer of varnish.
Grease the top with paste and secure the tulip.
Leave the rod for a day for the glue to harden.

Replacing pass rings

In order not to compromise the strength of the fishing rod, the rings are attached to it only with overhead staples or by winding.
First, you need to mark where the rings are installed on the rod. After this, the old rings are removed, preheated with a gas burner, and the remaining glue is removed. To install the ring you will need a smooth steel wire 0.1 mm thick and a thin silk thread. The wire is folded in half and placed along the rod, pressing the tails with the palm of your hand and leaving the loop free. Use your fingers to hold the ring and secure it with a thread tied into a “noose”. The thread is wound away from you and as tightly as possible, turn to turn, until it completely covers the leg of the ring. In this case, you need to lay a short tail of thread and a wire folded in half under the turns.

After winding, the end of the thread is passed through a wire loop and pulled to the opposite side. Now it is enough to pull the ends firmly in different directions to check the quality of the winding. If the thread was wound correctly, the turns will not move, and the bandage will be carefully fixed. The ends of the thread are cut and burned with a torch.

The ring is wound on the other side in exactly the same way. The thread is coated with a layer of two-component epoxy glue and left to dry. In order to give the rod a more aesthetic appearance, the places where the rings are placed are covered with adhesive PVC tape or heat-shrinkable tube to match the color of the rod.

Arrangement of rings

The rings on the form must be located on the same line in order. In order to correctly position the elements, you must perform the following steps step by step:

Traditional way.
The base is the leading component.
The outermost part is considered as the top of the structure.
New concept.
The first element is shifted to the middle of the structure.
Small parts allow the main line to pass through them.

Location Features:

Linear arrangement.
An average of 5-6 rings are used.
The fewer the rings, the more the bait casting distance increases.

In order to check the reliability of the design, it is necessary to combine all elements at the same time. This will help you understand the correct fixation of the elements and detect any errors in the work.

Repairing the guide ring on a fishing rod

Most often, the repair and maintenance of fishing gear has to be done by residents of the outback, where there are no specialized workshops where you can take your favorite spinning rod to replace, for example, a pass ring.

You should examine the ring inserts very carefully (preferably with a magnifying glass). Especially if fishing causes accelerated wear of the cord or fishing line.

A serious chip is noticeable immediately, but often only a crack appears, which is difficult to see, and it significantly spoils the fishing line. This ring needs to be replaced.

This work is not difficult, but requires accuracy. Therefore, before starting it, it is worth practicing on a failed rod or a suitable tube.

The old ring winding must be carefully removed. After cutting the mounting thread, heat the remaining varnish with a stream of boiling water, and degrease the installation site with a solvent.

To prevent the ring from moving during the winding process, you should first glue it to the form with hot glue. Which makes it possible to precisely fit the ring in place and improves the connection between the ring foot and the blank.

Freezing of rings

Icing of the rings is common during winter fishing. The main reasons are considered:

Low temperature conditions (most often icing occurs at 0°C and below).
Strong cold wind.

There are methods that help cope with this trouble:

Silicone lubricant in the form of an aerosol version (the effect lasts about 1.5 hours, after which the procedure must be repeated).
A popular remedy is Balzer or Kormarov ointment.
If the ring is frozen and there is no remedy, you can lower the tip of the spinning rod into the water for a few seconds.