Spinning rods for fishing from a boat

Spinning fishing from a boat

Having a boat gives the spinner a huge advantage and allows him to fish in almost all interesting places - and especially those areas where full-fledged shore fishing is impossible. This, for example, is the outer border of algae, the water area opposite dense thickets of bushes, and in general all places where you simply cannot reach from the shore. That is, a boat is not a luxury, but our indispensable assistant when fishing. It is clear that it is possible to correctly “tap” the riverbed and fish the extensive riffle only from a boat. And with a heavy jig it’s easy to explore even the deepest hole. In addition, if there is no bite, the boat allows you to radically change fishing: from coastal to deep, and vice versa - so we are unlikely to be left without a catch.

However, it should be remembered that the fish sees and “hears” the boat well, so you need to maintain at least basic silence. The greater the depth at the fishing spot and the further the cast, the less we alert predators. Therefore, the technique of fishing from a boat can be different. For example, you can “jig” at depth while standing, but it is advisable to cast along the very shore or grass while sitting, so as not to scare the fish again.

Fishing for pike in summer using a spinning rod: fishing techniques and tips for beginners

Experienced pike fishermen know that the most successful time for fishing for “toothy” is autumn and spring. It is during these periods that the predator eats, when it either eats up before winter or before spawning, with the warming of the water.

However, with the onset of summer, the water becomes too warm, which affects the activity of pike. And there are no problems with food, “prey” for every taste is teeming everywhere, so it becomes difficult to surprise the pike. But we will try to do it! Don’t put off your favorite spinning rod until better times, right? The one who searches and tries will definitely succeed.

Fishing in early June, when the water has not yet warmed up, can bring good results for pike. But as soon as the temperature rises, the predator abruptly changes its June stops to find itself in more comfortable conditions. And where you caught the “spotted” one in the first days of summer, you can no longer find it in July. In August, especially as it gets colder, the pike changes its location again.

It turns out that pike fishing in the summer can be divided into three periods, during which our fellow hobbyist will have to completely rebuild his strategy and look for other promising places.

Let's talk about all this in more detail and start with gear. What do we need for successful predator fishing?

In summer, it is worth preparing a full range of spinning baits for pike. You never know what might shoot out. Wobblers, rubber and various spinners work well. For fishing in conditions of abundant vegetation, it is advisable to have spinnerbaits in your fishing chest; they can be classified as classic summer baits, which will allow you to not be afraid of getting hooked. Of course, there is no 100% guarantee, but the risk is still minimal.

Wobblers with different depths can be used. Fishermen speak well of poppers, which attract predators with their “gurgling” sound. Or vice versa, use recessed models. Because when fishing at great depths, “surface fish” are unlikely to reveal their maximum potential.

For spinners, be sure to try spinners and spinners of different sizes. Do reconnaissance at different depths, experiment with wiring. In some places a uniform will work well, in others a classic step, do not forget to use elements of twitching if the type of bait allows it.

And, of course, the good old jig in all its equipment options. Oddly enough, pike can “take” large silicone even in July, despite the peak of passivity due to the water temperature and its bloom. However, there is an opinion that by mid-summer and early August it is necessary to “decrease”. Whether this is true, you can only check by fishing.

In general, when it comes to fishing tips on lures, you can never say for sure what will be useful to you. And if someone advises taking a specific model in an article on the Internet, like: “Top 10 catchable lures for pike in the summer,” most likely they are pursuing some kind of marketing goal, with a 90% probability.

But there are exceptions... I remember it happened on one of the summer fishing trips. Before the training camp, I received advice from a friend: “Take this lure, it works!” Although the attitude towards all this was skeptical, the bait still ended up in the box. And in the end it turned out that she received the bulk of the bites. When changing to another piece of hardware, the bite died down. Coincidence? Don't think.

Boat and its equipment

For fishing to be enjoyable, the boat must be equipped with everything minimally necessary for fishing.

First of all, you need a fairly heavy and “catchy” anchor with the necessary equipment. So far, the best rope is considered to be a parachute line - it does not “cut” your hands. To prevent the rope from getting tangled in your feet, it is advisable to wind it on a large floating reel-buoy made of durable polystyrene foam or polyethylene foam. Then, when hooked, it will be possible not to raise the anchor again and not frighten the fish. It will be enough to simply throw the reel and rope into the water, swim out and unhook the bait, then swim up again and anchor. The fastest and most reliable way to do this is with the help of the so-called “comb”, into the grooves of which the anchor rope is wound like a “snake” (Fig. 35).

Fig.35. Anchor equipment: a) assembled equipment, b) “comb”.

When removing the anchor, it is enough to loosen the tension of the rope or sling - and it easily comes out of the “comb”.

In addition to the anchor equipment, the boat should have stands for fishing rods so as not to scratch the forms, and especially the tips of the spinning rod, on the sides. The simplest option is the insulation of plumbing pipes cut along the “gut” (Fig. 36), placed on the back side of the boat.

Fig.36. The simplest stand for fishing rods.

In addition, the following items are usually taken into the boat: a box with baits and accessories, a landing net, an echo sounder or depth gauge, a release and a hook, a soft “seat”. It is advisable to take a landing net with the longest handle - ideally it should be a meter shorter than the length of the rod.

Spinning from a boat

To fish with a spinning rod from a boat, it is necessary to select a rod whose length will ensure casting to the required distance and at the same time it should provide comfort, even if there are several fishermen in the boat. The optimal length of the rod is 2.4 – 2.7 m. The characteristics of the rod are selected that will ensure the casting of the desired bait and the landing of the expected fish that lives in this reservoir. Most often, twitching wiring brings success.

When fishing with a spinning rod from a boat, it is advisable to use an echo sounder. After identifying promising places, it is necessary to conduct fishing at different depths. To do this, you need to periodically change the baits in your arsenal.

Preparing for fishing from a boat

The fishing plan is drawn up taking into account all the advantages that the boat gives us. After all, you can take several different spinning rods, a whole box of baits and much more into the boat. That is, we can have gear for almost any fish.

The route is selected accordingly and a plan is drawn up. As a rule, there will be a main fishing option, designed for a good bite and large fish, and a backup option in case of unfavorable conditions. For example, we hope for pike and zander from the depths, and if there is no bite, we move to the shore to catch perch and squint along the grass.

Such universal conditions dictate the most varied, and often even combined, tactics. You can stand all day in a promising place and wait for the mass “exit”; you can collect the catch one by one from several smaller “points”, or you can completely “comb” the border of coastal thickets. Not to mention that all these options can be combined in any way you like.

Again, the optimal plan and route must take into account many factors: the “biting schedule”, seasonal patterns, weather conditions, especially wind direction, sun position, current water level and the presence of current. However, the more options there are, the more difficult it is to take them all into account. If you can only walk along the shore in two directions, then by boat - go anywhere. Taking into account the fact that here we can quickly switch to other fish (after all, we have different gear and bait), it becomes impossible to take into account all the options and nuances. Therefore, in such “complex” cases, it is more correct to develop only the basic plan and route - and then in general terms. Let's hope that the rest will become clear "on the spot."

However, going out for serious fishing without a map or at least the simplest diagram of a reservoir means dooming yourself in advance to inadequate fishing.

Casting technique

To cast from a boat, you need to stand facing the stern, spread your legs slightly, and make sure that the bait does not hit the boat and your comrade. And only after that they cast with great force.

Casts can be over the shoulder (side) or over the head.

Side casting (left or right) is the most convenient for a one-handed rod. At the same time, a slightly bent arm is swung forward from bottom to top, and at the end the arm is extended in line with the rod.

The overhead throw is done using a similar principle.

There is also a sitting cast; its techniques are similar to those mentioned earlier. If desired, brake the line with your finger when casting.

It may happen that you have to use a two-handed spinning rod when fishing from a boat. In this case, the initial position of the rod is 45° to the water and you need to make sure that the bait is outside the boat before casting.

If the spinner (wobbler) is heavy, then the distance from the top of the rod to the tackle should be at least one meter.

More details about how to properly cast a spinning rod, not only from a boat, as well as the secret of long-distance casting are discussed in this article.

Initial adjustments to your boat fishing plan

On large bodies of water, where a boat is usually used, there are many more factors that can disrupt our plans. For example, a thermocline on a reservoir, as a rule, completely cancels deep fishing. However, if we know suitable “navels” or places of underwater springs, fishing can, on the contrary, break all records.

The bite of predators also greatly depends on the water level. As the level drops rapidly, at some point the coastal bushes and algae become dry. Here you can successfully fish for several days along the remains of the grass - then all the fish will move away from the shore to look for new sites. This means it’s time for us to switch to deep fishing.

Having a boat allows the angler to avoid some unfavorable conditions. For example, no matter how strong the wind is, you can always find a quiet bay or section of shore and fish there for your own pleasure. The only serious inconvenience that can overtake us in a boat is rain. Therefore, before an impending downpour, it is better to refrain from long trips - unless, of course, the boat is equipped with an awning.

Having assessed the weather factors, we proceed to inspect the reservoir. Just as with coastal fishing, we look for visual signs of the presence of fish and potentially successful places. If there are other boats on the pond, their number and location are assessed. This is where binoculars will especially help - after all, if one of the neighbors starts fishing for fish, we have the opportunity to “spy” the type and size of the predator, and sometimes even the bait. Especially remember the coordinates of “local” boats - as a rule, they are always in the right places.

Exploration and search for catchable fishing spots from a boat

The main task on an unfamiliar body of water is to find catchable fishing spots. Therefore, while we are sailing to the place, it is advisable to unobtrusively ask all the fishermen we meet: what kind of fish are they, what are they biting on, when and where? And so that they don’t think that we want to stand next to them and interfere with them, the question is formulated something like this: “Good morning. This is my first time here, swimming around that bend. Can you tell me what's interesting there? And how are you? And what kind of body of water is this anyway?”

The main task of reconnaissance is to determine an approximate picture of the depths. Therefore, if we have an echo sounder or an electronic depth gauge, we can immediately turn it on. In extreme cases, a regular depth gauge will do. It is enough to cross a body of water a couple of times and you will be able to imagine it “in cross-section.”

The next task: to determine the “working” depths - those at which the fish bite. There are several characteristic ranges: near the shore, up to 2 m, 3-4 m, 5-6 m and 7-10 m. We have already said that on certain days predators clearly adhere to certain depths. Therefore, it is advisable to consistently fish all ranges and determine which fish are located where. For example, perch stays at 2 meters, pike – at 3-4 m, pike perch – deeper than 6 m. All that remains is to choose who interests us most today, and in the future adhere to the desired depth.

Choosing the optimal bait and bait is in many ways similar to shore fishing. The only fundamental difference is that at a depth of over 3 m, due to its technical capabilities, it is difficult to find an alternative to jig baits. The only question is usually the choice between “rubber” and foam rubber, as well as the optimal load. Let me remind you that with active biting, a heavier head weight and faster retrieval are preferable. But for a passive predator, on the contrary, the lightest possible load and the slowest retrieve are better suited.

Choosing the right spinning rod

Action is a very important characteristic of a fishing rod!

Choose a spinning rod of short length , although this reduces the casting range, but this is not so important when fishing from a boat.

In a spinning rod, the power (thickness of the lower part) and the test must be balanced, but with a short length this is difficult to achieve with a telescopic rod. The connection of the rod knees should not have any play and should be without deformation.

For fishing from a boat, a plug rod made of carbon (graphite, carbon fiber, carbon fiber) with metal-ceramic rings (for example, aluminum oxide) is suitable. The rings are located in one straight line and do not have a single chip or roughness.

The rubber handle of the spinning rod must have a balsa wood insert.

The spinning test must correspond to the weight of the spinner (wobbler, jig head). The lower limit indicates the minimum weight of the bait, and the upper limit indicates the maximum weight of the bait. It is better to choose a rod with a test weight of 5 - 25 g.

By the way, you can see fishing rods on sale that indicate the recommended range of fishing lines with breaking load.

Depending on the type of fish, you can give a table for a more simplified selection of a fishing rod :

Let us separately analyze the length of the spinning rod

As you can see, a spinning rod with a length of 1.80 m to 2.40 m is quite enough, but when fishing from a small rubber boat, you can go even shorter – 1.6-2.1 m. Let's give a few examples.

Fishing with a wobbler:

• Slow or medium (Regular Fast, Regular, Mod-Fast, Moderate) action with a light rod.
• Fishing with a minnow wobbler. Build fast or extra fast. The length of the spinning rod is 1.8 - 2.1 m, with a dough of 5-14 g (wobbler 3-7 cm in length), 5-25 g (for large wobblers).

Jig spinning rod . There are two options here:

• At great depths and currents. Light and rigid with the fastest possible action (fast or extra fast). Length 2.1 – 2.4 m. Test 10 – 50 g.
• On the lake. The build is medium with a dough of 5 - 20, or fast with a dough of 5 -15 g, or ultra-fast with a dough of 3 - 12 g.

And:

• Lure fishing . Slow action (Slow) with dough 3-12, 5-15, 5-25 g.
• Fishing with a jerkbait . Medium tuning (Regular Fast, Regular). Light rod with a length of 1.6-2.1 m. The upper limit of the test is 100 - 150 g.

Basic fishing from a boat

Regardless of which route we choose, we don’t forget to record the biting “schedule” and remember the catch spots. A schematic map of a reservoir with a marked riverbed and other landmarks is perfect for this.

Since the boat route is usually return, in the middle of fishing you need to make a conclusion: return to the old “points” or to new places. If, for example, morning fishing along the riverbed did not bring significant results, it is perhaps better to sail along the shore on the way back.

Another advantage of boat fishing is the possible presence of several equipped spinning rods. This makes fishing more efficient. For example, when fishing for pike, a perch “fight” suddenly began - we take a spare spinning rod with a popper and immediately catch the “striped ones”. The “exit” has stopped – we switch back to the pike.

However, even when catching the same predators, it is advisable to periodically alternate baits. It has been verified that even a large school of perch, after catching several relatives, begins to be suspicious of the catchy model - up to the complete cessation of bites. And here, a timely replacement will allow you to prolong the bite. It’s not for nothing that experienced spinning anglers, even when they’re hungry, alternate baits every 10-20 casts if necessary. By the way, when catching large predators at the “point”, this technique often brings long-awaited success. Therefore, here, too, a pair of equipped spinning rods will come in handy.

Features of fishing techniques from a boat

• If the fisherman is sitting at the bow or stern, then cast the spoon over his head.
• At great depths and fishing near the bottom, the reel is reeled in slowly with pauses. Moreover, after touching the bottom, the tackle waits a little. You can determine the time by waiting 3-5 seconds after the bait touches the surface of the water.
• In shallow places, the bait is baited without immediately allowing a free fall.
• If the boat is drifting, then you can fish by casting or plumb (with winter bait). When fishing vertically, the rod is short and rigid.
• Places are chosen near algae, among snags sticking out of the water, near flooded bushes, between boulders
• During floods, after rain, casts are made towards the shore.
• In late autumn they catch fish near the far side of the pit.

Orientation on a body of water

When fishing from a boat, it is impossible to ignore a very important topic that deserves a separate section. After all, if navigation on a small river is not difficult, then on a vast body of water this can become a problem. And how then to find a small catchable “patch” on a large reservoir?

In principle, there are three ways to navigate a body of water: by “targets”, by compass and by navigator.

If a lake, reservoir or large river has winding banks with many characteristic objects (houses, bridges, piers, power lines, poles, towers, etc.), it is usually possible to “tie” any point of the reservoir to several coastal landmarks. The essence of the most common method is based on the geometric rule, according to which two straight lines intersect only at one point. This means that in order for the fisherman to find the desired “point”, he needs to stand at the intersection of any two conditional straight lines.

And to set one single straight line, only two points on the ground are enough. We need two straight lines and, therefore, two pairs of points. Therefore, let's look around and outline several noticeable nearby landmarks, so that in the future we will leave only the two most convenient ones. Having mentally connected the boat and the nearest landmark with a conditional line, we continue this line and look for a second, distant landmark on it. For example, it could be a separate tree on the shore and paired with it a noticeable house, a tower, or a clearing in the forest in the distance. Next time, combining the first pair of landmarks will give us one exact direction to the desired point. We follow exactly this “alignment” until another “alignment” aligns, that is, another pair of landmarks (Fig. 37). That's it, we're already there.

Fig.37. Orientation along the “targets”.

In this case, the error will be minimal if the “targets” are located crosswise at an angle close to 90°, and the distance between the near and far landmarks is maximum. In such conditions, the accuracy of positioning is very high. There has long been a story about how one experienced fisherman dropped an expensive knife into the water from a boat. Having accurately noticed the “targets”, the next day he sailed here and lowered a strong magnet on a rope - almost the first time the loss was safely returned.

However, what to do if the banks are monotonous and there are almost no characteristic landmarks? In this case, we will need an accurate compass with a sight. We will always find some two landmarks, and with the help of a compass we can determine their exact azimuth in degrees of circumference. In principle, this is already enough to put it in place - although not so quickly, but still relatively accurately.

In all other cases - for example, in a wide open space or in fog - only the navigator will help us. This is a special device that uses satellite signals to accurately determine coordinates on the ground. Different models have an error of 5 to 50 m, which is comparable to the casting distance and is quite enough for spinning anglers. But the navigator also has a lot of other useful functions - for example, the average model has a memory for 150 points, 10 routes and even, if necessary, a full “link” to the map. I know from myself that it’s a useful thing!

Features of fishing or comparative analysis of catching fish from the shore and boat

If you think that catching a predator from the shore and fishing from a boat are the same thing, you are mistaken. After all, for long-distance casting from the shore you need a rod 2.7 - 3.6 meters long. Whereas when hunting a predator, a short stick of 2.59 cm is enough, and for trolling even less, only 1.50 cm.

When fishing from the shore, you can use a thinner fishing line or cord than when catching fish from a boat.

Fishing from the shore is a limited space with casting range. At the same time, a fisherman on the coastline has certain advantages. He can feed a promising place. But this applies to a greater extent to catching white fish, but not a predator.

Let's sum it up

Agree that in one article it is impossible to fully reveal all the features and subtleties of catching a predator from a boat. The issues of choosing a boat and engine power remain unclear. The question of using an electric power unit is open.

There are nuances of equipment for catching a predator from a boat, and of course, the issue of behavior in the boat and safety remains open. Read about this and much more related to catching a predator from a boat in the following articles!

It doesn't matter what size your trophy is. Most importantly, have fun being on the water and connecting with nature!

River rafting fishing

A special role in fishing is played by raft fishing, when the boat moves independently with the current or wind. The speed in this case is usually low, so the fishing itself is quite convenient and very rational. After all, almost all the time is spent only on “clean” fishing and minor adjustments to the movement. But in a day a huge area of ​​water is fished - and the result is usually appropriate.

Already from the introduction it is clear that raft fishing is especially effective in relatively “uniform” bodies of water, where there are no clearly defined catch spots, and the fish are dispersed throughout the water area. Although here we can anchor at any time and continue fishing in a stationary mode. Which, by the way, often happens in bodies of water without a current, where rafting is carried out only in areas with a fair wind, and in the rest of the water area fishing follows different rules.

But it is most convenient to fish by rafting on medium and large lowland rivers. The optimal flow speed is 2-5 km/h - it ensures both correct wiring and a sufficient “combing” interval. If absolutely necessary, the speed of movement can be reduced with the help of a so-called “water” parachute, which also maintains the orientation of the boat, preventing it from spinning.

The most rational way to fish is by rafting from a rubber boat - it’s easiest to use some kind of transport up the river and then go downstream to your house or to the desired bus stop. After all, the best places are usually higher than large cities. And if this is not the case, it is better to start rafting right from home - then if unforeseen circumstances arise (prolonged rain or a boat puncture), you can return faster.

Usually, rafting fishing is “tied” to a characteristic longitudinal section of the river - to the outer border of algae or to the channel edge. Sometimes fishing is carried out along the riverbed itself or even along the coastal plateau - if the river does not have pronounced edges.

Perhaps the most popular method is fishing along the edge of algae. Our main catch here is pike and perch. In this case, the boat is launched either along the grass itself, or a little further away. The best baits are non-snagging “oscillators” and twisters on light jig heads, spinnerbaits, sinking and diving wobblers. The bait is thrown to the grass itself or into the “corridors” between the algae, where predators stand in ambush - and the bite usually follows within the first meters of the retrieve. “Unhooked” ones are more convenient here; you can throw them directly into the thicket, and then slowly pull them off - there will be more bites, but also more escapes.

But for deep raft fishing, the best baits are definitely “rubber” and foam rubber. The boat here is launched either parallel to the edge at a relatively short distance, or along the plateau - but usually not closer than the shore casting distance, so as not to fish along a strip that has already been “combed” from the shore.

With a light tailwind, it is enough to take the desired course and fish, fish, fish... And if the fish are biting well and the weather is good, then raft fishing is generally an incomparable pleasure. Just have time to take pictures of the fish and record catchable “points” and even entire sections of the river in your notebook. By the way, sometimes in such cases or when catching outstanding specimens you have to stop and even temporarily turn back.

The best spinning rods for fishing from a boat

For any fishing method, choose a device with a finished length of 2.1 - 2.4 m. A large parameter value will complicate landing fish. For small bodies of water, spinning rods with a test weight of at least 20 g are produced, for rivers, taking into account the current, from 25 to 50 g. The presence of a rigid blank ensures good sensitivity. The models are suitable for precise casting in cramped conditions. Compared to the average action, they have less range and hold fish worse. Analysis of comparative tests and user reviews made it possible to select 7 best spinning rods for fishing from a boat out of 10 nominees.

Major Craft Dodger Dgs-752mh

The medium-heavy class device is designed for a bait weight of 7–28 g. The blank is made of graphite material, which ensures lightness, strength, and good sensitivity. The design feature is increased taper. In the butt part the spinning rod is thick, but quickly turns into a thin tip of medium hardness. The extra-fast action ensures precise casting and penetrates the fish's mouth well. The length of the rod when assembled is 1.17 m, when finished – 2.26 m.

Advantages

• Plug design;
• Light weight;
• The arrangement of the rings ensures accurate casting with a good distance;
• Full process control;
• Suitable for prey weighing up to 8 kg;
• Reel holder handle made of cork and EVA material.

Flaws

• High price;
• Fragility when hooked.

Users position the model as a spinning rod for jigging from a boat. It is less effective with other fishing methods. The advantages include good endurance; there are cases of pike catching 11 kg in a river with a current. It is noted that after 2 – 3 jerks when hooking, the top flies apart.

Daiwa Specialist-R 702 Mls (Sp702mls-R)

The plug design model is presented in the lightweight class. Designed for lures weighing 4 - 18 g. Fast action indicates better opening when fishing with jigs or wobblers. The length of the assembled spinning rod is 1.1 m, the total length is 2.10 m. Carbon fiber is used in the production of the blank, the material of the rings and handle is almost identical in quality to the previous nominee.

Advantages

• Compact;
• Light weight;
• Quality of materials;
• Good sensitivity;
• Casting accuracy;
• Not afraid of slight overload.

Flaws

• High price;
• Suitable for catching small fish.

Users believe that the model is suitable for jigging and twitching. The characteristics declared by the manufacturer are true. There are no complaints about quality or functionality.

Maximus Winner Msw24l

The plug-type spinning rod is suitable for fishing with various types of bait weighing 3–15 g. The graphite blank is equipped with 7 rings with SIC inserts. Their design resembles a tulip. Neoprene was used to produce the handle. The coil holder design improves sensitivity. The length and weight parameters exceed those of previous nominees.

Advantages

• Low price;
• Design;
• Strength;
• Effective for different fishing methods;
• High-quality assembly;
• Good throwing range.

Flaws

• Heavy.

Experienced fishermen believe that spinning is suitable for beginners. It is less suitable for gracefully guiding wobblers and making accurate casts in difficult conditions. The model is used mainly in shallow reservoirs for catching fish weighing up to 4 kg.

Shimano Vengeance Ax Spin Tele 240 M (Svaxte240m)

The telescopic spinning rod has good mobility during transportation and fishing. When assembled, the length is 0.68 m, and when finished it is not inferior to the size of plug-in models. The device is designed for baits weighing 10 - 30 g, so it is suitable for catching fish up to 6 kg. Anodized rings are made of steel. They are light but durable, provide a good casting distance, and keep the blank structure unchanged.

Advantages

• Average price;
• Compactness;
• The kit includes a protective case;
• Good sensitivity;
• Build quality.

Flaws

• Low strength;
• Weak coil attachment.

The model is easy to use and has good characteristics, although its behavior is not always clear after plug-in options. The advantages include low price, versatility for beginner fishermen.

Best Braided Lines for Fishing

Salmo Elite Micro Jig 10 (2323-232)

Spinning rod for fishing with small jig baits. Their weight should not exceed 2 - 10 g. Lightweight rings with a silicon carbide insert are installed on the IM7 carbon fiber blank. This feature provides them with corrosion protection, high strength, and low weight. The transport length is 1.21 m, the total length is 2.32 m. The Over Steek connection of the knees involves inserting the lower into the upper.

Advantages

• Average price;
• Light weight;
• Fast build;
• Plug design;
• Handle made of EVA material;
• Screw reel seat;
• Good fighting.

Flaws

• Catching fish weighing no more than 2.5 kg.

Users note the versatility of the model, the comfort of the handle, the sensitivity of the whip, and the quality of the material. Spinning rods hold fish well in the current and are effective for landing large prey. The disadvantages include the high risk of breakage during transportation without a tube.

Black Hole Sterh S-240/4-18

Medium-class fishing tackle involves the use of baits weighing 4–18 g. The fast action ensures accurate casting without a strong swing in cramped conditions. The assembled length is 1.25 m, the total length is 2.4 m. The blank is 99% made of carbon. Rings with SIC inserts are lightweight, have good strength, and are protected from corrosion. The spinning rod is universal in terms of the type of bait used. The handle of the spaced type is covered with EVA material.

Advantages

• High sensitivity;
• Clear hooking;
• Comfortable handle;
• Plug design;
• Average price.

Flaws

• Graphite quality.

The majority of respondents highly rate the nominee's parameters. Spinning rods are easy to use, good for fishing, and effective for different methods of fishing. The downside is the fragility of the form; with strong jerks on the toe, it quickly breaks.

AIKO Ranger RAN210M (111-404)

The model from the series of twitching rods is focused on jerking with wobblers. With a middle-class spinning rod, most of the blank works when under load, so you need open space for casting. The device has a compact size. The assembled length is 1.1 m, the total length is 2.1 m. The rod test involves the use of baits weighing 5 - 28 g. The rings are made of high-strength aluminum oxide.

Advantages

• Suitable for catching medium and large fish;
• Light weight;
• Average price;
• Casting range, accuracy;
• Graphite blank;
• Plug design;
• Moisture resistance of the handle material.

Flaws

• Unreliability of blank connections.

Users find virtually no downsides in this PVC spinning boat. It has good sensitivity and casting range. At a low price, the disadvantages are considered insignificant.

Collective fishing from a boat

Group fishing from boats is especially interesting. After all, here you can spread out in different directions and, without interfering with each other, fish for your pleasure. Thus, in a day, a large area of ​​water is checked - both deep and coastal, all kinds of gear and bait are tried, and a wide variety of fish are caught.

The only thing that needs to be thoroughly discussed is the initial collective plan, which should take into account as much as possible the passions and capabilities of all participants. After all, among spinning anglers there can be convinced “coast fishermen”, experienced “deep fishers” and simply “generalists” - naturally, each of them prefers “their own” fishing.

The main difficulty is the current exchange of information. It would be nice to get everyone together in a couple of hours, but often this turns out to be unrealistic. The problem is solved through walkie-talkies and mobile phones - for those who have them. The rest have to collect useful information along the way and through third parties. Nevertheless, if not all the news, then most of it can be found out at the reservoir. The full picture becomes clear only in the evening at the base or on the way back. And all the same, this is very valuable information that shows the overall picture of the bite in the entire reservoir.

Fishing together from one boat can also be considered as an option for group fishing. After all, here, too, until the situation is completely clarified, different baits and different wiring are usually used. For example, both anglers prefer jigs: but one fishes with “rubber” with a long “step”, and the other fishes with foam rubber with a “short” one. Another method is often used: the first one throws towards the shore, the second - into the depths.

That is, together you can also fish a double area of ​​water or “comb” any area twice as tightly. However, there are no longer opportunities for broad collective reconnaissance here. But you can immediately compare different baits and fishing options, and the exchange of information occurs instantly. The optimal fishing pattern is gradually determined, and then the gambling competition begins - who will win!

The only condition: to correctly arrange all the gear and agree on the sequence of casting and the order of fishing - in order to catch the fish, and not each other. Well, fishing together is doubly fun. And the total catch is always greater. And if you suddenly come across a “crocodile”, a friend will always help you pull it out.

Choosing a rod, which spinning rod is better for fishing from a boat?

When hunting predatory fish using a boat, you need a shorter spinning rod than when fishing from the shore. This is due to limited space. In addition, there is no need to make long casts. You can approach a promising place. As practice shows, for comfortable casting from a boat, a rod with a length of 8 feet 6 inches is sufficient, which corresponds to approximately 2.59 cm. The minimum length of a stick is 150-180 cm. Therefore, a short spinning rod for fishing from a boat is the most effective weapon for fishermen. The main thing is convenience.

Choose a medium or fast rod action. The test can range from 10 to 40 grams. We do not recommend using parabolic and semi-parabolic spinning rods for fishing from a boat, especially when trolling, as they are softer. When catching a predator, especially pike, there will be a large number of idle bites and annoying escapes.