Amphipod for pike perch: drawings, description, wiring technique

Amphipod when fishing for pike perch. Design.

The presence of a suspension in the horizontal plane and the working manner in such positions make it possible to classify the amphipod as a spinner. Just like the balancer, the amphipod can be confidently called a spinner. Structure and main features:

• Flat shape and different width sides. This design makes it possible for the tackle to fall on its sides during the wiring process;
• The passage of the monofilament thread is ensured by a through hole located in the center. A ring and a tee are attached to this thread.
• A tee with a wool brush is soldered to the back. It replaced the plastic tail and plays the role of a stabilizing link. Interesting fact! In this situation, there is no hook in front of the bait.

What is an amphipod spoon and what does it look like?

An amphipod is an artificial bait with a shifted center of gravity, which is successfully used for winter fishing for predators, especially pike perch. This does not mean that another predator, such as perch or pike, cannot bite on amphipods, but the “game” of this bait is most attractive specifically for pike perch and anglers use this successfully.

Recommended reading: Details about spring feeder fishing

Due to the fact that the center of gravity of the bait is shifted, when retrieving it, it moves in a circle with a radius of no more than one meter. That is, even in one pass you can fish a large area and provoke the fish to bite.

Amphipods have a vertical suspension, but still play horizontally and at the same time resemble a flat balance beam. That is why experts classify amphipods for pike perch as horizontal spoons, which provide powerful vibrations in the water and thus attract the attention of the predator. The sides of the amphipod’s body differ in thickness, and because of this, when retrieving, the effect of “falling over” the bait occurs.

Making the correct wiring of the amphipod

The well-known 8x8 wiring style plays a major role here. We make eight strokes up and down with pauses of eight seconds. All actions are performed in only the 1st hole. The action plan is as follows:

1. We lower the tackle into the hole of the hole. There should be 15-20 cm left to the bottom.
2. Slowly raise our amphipod 25 cm higher. Then, with a quick movement, we throw it back to its original location.
3. We wait 8 seconds and repeat the maneuver. The number of such strokes is no more than 8.

There is no need to exceed the time. These movements will not bring any sense.

If there is prey in the hole, it will show itself. Even the appearance of a toss or a slight nod will indicate the presence of a predator. If there are no urges, there is no point in continuing. The chance that everything will end successfully is very small.

We catch the coveted pike perch using an amphipod

Thanks to its sharpened shape, this tackle will be a good helper for winter fishing for pike perch. At this time of year, the predator actively leaves its habitable places in search of food. If the pike perch is full and does not feel hungry, getting it to bite the bait is very problematic. Exceptions may be fry.

In the winter season, for successful fishing, you should find a wintering place for pike perch, and only then start hunting. This is due to the fact that in winter the predator disperses throughout the entire water area. In addition, pike perch can be considered a gourmet fish. He meticulously chooses not only the bait, but also the manner of its behavior - that is, the game of the fisherman, who acts as a bait manipulator. For good fishing, the retrieve should be done slowly, with light waddling movements. It is worth taking note: the bait should not be far from the fish. The close proximity of the gear to a predator increases the chance of a good catch.

What is amphipod?

Amphipod is a bait designed for catching predatory fish from ice or vertical fishing from a boat. Due to its design features, this bait sinks as quickly as possible.

Despite the absence of blades and fins, the amphipod has a pronounced specific gliding game, which is why the bait simply drives all predators crazy. The absence of additional plastic elements makes the bait resistant to breakage and deformation.

It is advisable to have a dozen amphipods in your arsenal in order to be able to experiment and choose the ideal game and bait for the mood of the pike perch.

Gear used for bait and bait when fishing for pike perch

The bait looks more attractive to fish if you use bait in addition to them. Among the variety of materials, the most popular and effective ones have proven to be:

• A piece of cambric;
• A small piece of fabric;
• Natural wool thread;
• Painted foam.

A good solution would be to use bait made from natural materials. For example, individual parts of a fish (tail or eyeballs) work well. The variety of choices depends on the preferences of the fisherman.

Recommended game and jig retrieve when fishing for perch

This jig works best in a stepped retrieve. First, the amphipod sinks to the very bottom for 10 seconds, then they need to lightly tap on the bottom, this creates the illusion of a mollusk burrowing into the sand; if during this period the fish does not bite, you need to start a small but intense game with ten-second pauses, gradually raising the tackle to the surface.

Perch can decide to bite at the very last moment directly under the ice. Chub can also bite on this bait. If you stop playing, the amphipod will quickly sink to the bottom, and during the game its body and legs bounce and sway. You can fish with such a jig even in the summer season; the catch with it, as a rule, is very good, and the production is elementary. The main thing is to learn how to operate it correctly and prevent the thread legs from freezing in winter.

Belikov A.A. ,Russia,Volgograd - Especially for the site Homemade FISH

• Braided jig for catching perch with a nozzle
• Catching large perch using small fins

We make our own amphipod for catching pike perch

Each fisherman has his own method of making bait. But we should highlight those that are more popular and easier to manufacture.

Method No. 1

It’s not for nothing that this method was numbered first. It has no equal in ease of manufacture. The minimum set of ingredients to create such bait is available to everyone. So, we will need:

1. A piece of paralon or foam;
2. Fishing hooks from numbers one to five.
3. 4 mm in diameter tungsten or lead pellets in gray or black colors.

Where do we start:

1. We prepare the workpiece from the selected material. The workpiece should have a longitudinal shape with a thickness of 2-3 mm.
2. We place the workpiece on the fishing hook, distributing it along the entire length of the hook.
3. Stretch the thread and cut the tip to 5 mm in length. This design will imitate the movement of crustaceans. The bait is ready!

Method No. 2

For production you will need:

• Wood block;
• Ordinary scissors;
• Material that is easy to process (foam for example);
• Ruler;
• Scotch tape, or in the absence of such, masking tape;
• Lead;
• Alabaster;
• Fishing hooks;
• Knife;
• Brilliant copper solution (Zelyonka in common parlance);
• Wool brush and paint.

Sequence of actions: Step 1. Create a layout of the “amphipod”. This can be done in two ways: A) We make a model by cutting it out of foam plastic or any other material that can be easily processed. However, it is worth considering that the quality of processing will affect the outcome of the workpiece. B) We prepare in advance a small wooden block, which we then cover with either adhesive tape or masking tape. In this way we prepare the formwork for the future form. By the way, half of this shape should be at least 20 mm high. Step 2. Prepare a solution of alabaster and pour it into the mold. Step 3. Lubricate the workpiece with soapy water and wait until it dries. Then we immerse the workpiece in the mold until the alabaster dries or curls. Step 4. Using a knife, create 2 holes in a conical shape. This is a kind of “mother” that will become a guide for the second half of the workpiece. Step 5. Treat the entire surface with a soap solution. Step 6. Create the formwork and fill it with mortar. Step 7. After the mold is divided, we begin to create the sprue and groove for the hook. Leave to dry, after removing excess. Step 8. Lead pouring becomes excellent due to the fact that the alabaster mold has a low level of thermal conductivity. If you have the desire and strength, you can pay attention to the little things and scratch peculiar scales on the workpiece. However, this should only be done if the form is completely dry. Carving a wet piece will cause the lead to pop out of the mold. Step 9. A good tip for successful fishing: paint the sides of the amphipod in different colors. One of the sidewalls can be made green by adding greenery to the solution. Step 10. Determine the center of gravity of the gear. To do this, we place it on the edge of our ruler. The hole should be made in a place that will allow the tackle to hang with the front part slightly raised up. In addition to this, one of the ribs of the amphipod should be visually raised above the other. Step 11. Give the bait an aesthetic appearance and attractiveness. To do this, let's start painting. We treat the parts with a primer solution, then paint them with base white enamel, or any other shades to suit the fisherman’s taste. Often, bright lemon shades are used instead of white. Step 12. Attach a wool brush as a tail and fix the tee. The product is ready! You can start fishing!

Making your own bait

Many novice fishermen are often interested in the topic of creating a “Bokoplav” spoon for pike perch.
Making such a bait is not a very complicated procedure, so if you follow some rules and a step-by-step guide, everything will be very simple. There are several manufacturing methods and instructions, but this one is considered the simplest and most accessible. From the materials you will need to take:

• A piece of polystyrene foam or foam rubber.
• A lead or tungsten pellet, about 4 millimeters thick.
• Hooks numbered 1 to 5.

At the first stage of manufacturing, you need to cut a blank from a foam or foam plate. Its thickness will be 2-3 millimeters. In this case, the product must be longitudinal. Next, you need to put the workpiece on the hook along its entire length, and after a few millimeters, pull the thread and cut it, leaving a tip about 5 millimeters long. It is this part that will be used as paws.

With the help of such a simple design, you can try to catch fish in a pond.

Complicated creation option

There is a second option for making amphipods, which involves the use of such materials and improvised means:

• Lead.
• A piece of wood.
• Polystyrene foam or any other product for the workpiece.
• Scissors, ruler and adhesive tape.
• Alabaster.
• Knife.
• Tee and hooks.
• Zelenka.
• Paint and brush for painting.

Next you will need to take a piece of wood and cover it on both sides with tape. This way you will create the so-called formwork, which will allow you to move on to the next step. By the way, the height of this formwork should not be less than 20 mm.

At the next stage, you need to prepare an alabaster solution and pour it into this form. Do not forget that such a substance can harden quickly, so after leveling the solution, the workpiece must be half immersed in it. Before this, it is pre-lubricated with a soap-based solution to make the workpiece easier to remove from the mold. Typically, it takes 15 to 20 minutes to completely cure. Once this time has expired, you can continue working.

Take a knife in your hands and make 2 indentations that will act as guides for the second half of the product. Using a soap solution, it is necessary to process the entire structure along with the workpiece, and then make a formwork from adhesive tape and fill it with alabaster.

As soon as it hardens, the two parts must be separated and the workpiece pulled out. Holes for filling are cut with a knife: there should be at least two of them. Air will come out of one when lead is poured into the other. After performing these steps, the filling form must be dried. The main thing is that it dries well enough. Do not speed up this process, as this may worsen the strength properties.

Final coloring

If you intend to create the Bokoplav spinner using the second method and have followed the above instructions, then you next need to paint the created blank green, possibly with brilliant green. In this case, it will be more attractive to fish.

The next step is to determine the center of gravity. The main thing is that after immersion in the water the bait should be with its nose slightly raised, and one of the ribs should be located higher than the other. Take this feature into account in advance, and only after that start drilling a hole for mounting.

Read How to make a catfish snack with your own hands

Ultimately, it is necessary to give the bait an aesthetic appeal using a coloring agent. But before starting this work, the part must be cleaned of burrs or waste.

There are a wide variety of paint options, but each deep-dweller has his own personal preferences in this regard. If we are talking about catching perch or pike perch, then it is advisable to use bright lemon tones.

There is also one more important step to complete - form the tail and secure the tee. Having done this, the bait can be considered ready for use.

How to knit amphipod correctly?

When tying amphipods, you can use a couple of methods:

1. We tie it on the side of our gear. We draw a monofilament thread into the wide opening of the cavity. And only then, on top of the thread, we fasten the tee.
2. Tying by installing a corkscrew on the monofilament. Then we make a tee and a subsequent corkscrew. The end of the fishing line must be inserted through the tackle and secured to the tee. It's similar to a marmouse.

Where can you buy amphipods for pike perch?

Buying such a product will not require much searching and effort. Everything is decided here by the possibilities and the fisherman’s wallet. If you have the opportunity to go to a fishing store, then take advantage of it. Inspect the gear live and take a closer look at the models. You can also order on the Internet. Purchasing through an online store will save time. And the opportunity to get an online consultation will make the task easier when choosing an amphipod. Have you decided on the model? Then all you have to do is make the payment, and the treasured gear will go to its owner. In addition, home delivery is another advantage of online shopping.

A good catch is not a matter of luck and a light hand. Properly selected equipment, the ability to find the right range for fishing, smart selection of bait and many other nuances - this is not the whole list that is needed for good fishing. With all the set of these devices and human qualities, the fishing process brings the highest success!