DIY fishing net planting

Tackle characteristics

Currently, fishing websites offer a lot of instructions on how to weave nets by hand for beginners.
This skill can be useful not only for fishing enthusiasts, but also for more experienced fans who want to expand their professional experience. It is no secret that each fishing net has a different weaving method and different mesh sizes. The last parameter is determined by the following factors:

Estimated production size.
Method of fishing.

If anyone has had to weave a tackle from nylon or ordinary fishing line, then he knows how complex and painstaking the upcoming process can become. In any case, if you take it seriously, the end result can exceed your initial expectations.

The networks available on the market come in different shapes. Single-wall and two- or three-wall models are in greatest demand. The first option is considered the simplest and most common. At the same time, it is used for both amateur and commercial purposes.

As for modernized products with two or three walls, they are called “entanglements” (the principle of operation is to entangle fish). The prey becomes entangled in the net and can no longer escape to freedom.

When choosing the length of the net, several subtleties are taken into account, including the environment in which the fish will be searched. A universal option is a 20-meter tackle, with a height of 1.5 to 1.8 meters.

Another important characteristic of the gear is the size of the cells. It is selected in accordance with the amount of expected production according to the following parameters:

Nets with a mesh diameter of 20 mm are ideal for catching live bait and small aquatic life.
The diameter of 27-32 mm is intended for catching roach and perch.
Diameter 40−50 mm is an ideal solution for fishing for bream and crucian carp.
Nets with mesh sizes from 120 to 140 mm are a powerful tool for catching pike.

How to plant fishing nets with your own hands

Planting fishing nets with your own hands is a long process compared to the machine method. But this type of gear is more catchy and softer to work with.

How to plant a fishing net

Landing is the attachment of the net fabric to the cord, which can be done manually, by shuttle or by machine.

In order to make a fishing tool out of canvas, the net fabric must be placed on the upper and lower selection. A floating cord is used for the top selection, this makes it easier to set up the nets and unravel them.

Upper and lower cord length

The lower cargo cord is 20-30% longer than the upper one. This difference in lengths causes the net to sag. But such sagging is undesirable for the top, because the fish will become entangled. If the top floating line is longer than the bottom one, then the top part will be more catchy. This landing can be used for catching whitefish at the bottom or near the surface of a river; How to make a landing correctly can be determined by knowing the weight and buoyancy of the cords.

Due to different distances between network nodes, the lengths of the upper and lower cords also differ. The larger the gaps between the nodes, the longer the fit. Fishing gear with different cells has a different landing coefficient (PC).

Nodes used

The strength of the knots is influenced by the method of tying them and the materials used. Knots for planting fishing nets are made in several ways:

Make 2 turns around the edge with the cord. Then the working part of the cord comes back and is threaded through the fishing line that remains behind. It drags on.
The "Pig's Hoof" knot is tied with a safety loop at the back. The cord is threaded under the edge and wrapped behind the base to form a loop around the edge. The other end of the line makes a turn after 2 loops when counting from right to left.
The Triple Hoof Knot is performed in the same way, but there will be 3 loops.

The line is tightened in the direction in which it twists itself.

Planting methods

There are several planting methods:

“on the run” method - without fastening nodes, which will allow the net fabric to move along the landing thread;
drift method - using a special leg, thanks to which the canvas does not twist into the collection;
“in a knot” - used for large-mesh fabric;
landing on cords is typical for fabric with small cells.

There are several ways to plant a network - using the Finnish method or the rectangular one. With the Finnish style, the length of the upper selection is reduced, and the length of the lower selection is increased. When rectangular, the length of the cords of the upper and lower selections is the same.

Using shuttle

The shuttle is used for manual weaving of mesh fabric and for planting it on pick-ups. The shuttle is passed through the outer cells, which are tied to a picking cord. Again it is skipped and fixed. This must be repeated until all the cells are secured.

Using special machines

Fishing gear can be produced using machine knitting. The entire weaving process is performed automatically. One knitting machine can produce products with different mesh sizes. The cell size depends on the set parameters and is adjusted manually. The machine can knit with any type of thread.

Planting a network with your own hands

To make fishing gear with your own hands, you need the following tools:

ruler;
shuttle;
monofilament scaffolding or strong thread.

Weaving is done like this:

a fishing line is attached to the shuttle;
the end of the thread from the shuttle and the outermost cell are tied to the cord;
then you need to thread the cells into the shuttle;
after this, the shuttle thread is attached to the adjacent markings on the cord.

In order to position the net correctly in the future, sinkers and floats are used when landing.

What is a milestone for?

A milestone is a special ruler with notches made on both sides. Then mark the values of the intervals between the nodes by applying a pole to the power cord.

Landing requirements depending on the purpose of the network

Fishing gear is as follows:

A canvas with thick cells is used when planting a seine. Strains the fish.
Those that wrap around fish by the gills are used in bets; it is advisable to use this type of fishing net in bodies of water without a current.
Three-walled - they have large cells on the sides and small ones in the middle. These are used to catch large and small fish.
Floating - a rectangular canvas with a cell size corresponding to the size of the prey, used in currents, drifting with the boat.
Spawning - the mesh fabric is cut into 2 or 3 parts. Used in shallow water.

Before placing a net on the river, it is necessary to determine the location of the concentration of fish. There are no clear recommendations on how to set up a fishing net, but you need to consider in which rivers it is recommended to use certain gear.

Planting methods

There are several planting methods:

“on the run” method - without fastening nodes, which will allow the net fabric to move along the landing thread;
drift method - using a special leg, thanks to which the canvas does not twist into the collection;
“in a knot” - used for large-mesh fabric;
landing on cords is typical for fabric with small cells.

Using shuttle

There is no need to make large gaps between nodes to speed up work, because this will disturb the position of the canvas in the water.

Using special machines

What is the network “planted” on?

Seine weaving and its planting are technologically interconnected. What is this procedure? Planting fishing nets with your own hands involves attaching a net plane to a cord. Each mesh has two landings - upper and lower.

They serve for soft fastening of gear. But in order to control the net while fishing, you need to attach a stick to its entire side. And on both sides, people use them to regulate the movement of the network.

For example, for pike near the reeds, cast a net with an inclination similar to a scoop, as if you were hooking the fish at the bottom, forcing it to leave. But there is nowhere to go - the net is wrapped almost until the two sticks are completely connected: the result is a trap.

How to plant a fishing net with your own hands? This work is really done by amateur fishermen only by hand. But using the same shuttle as when weaving a network.

With the net planted, you need to get the hang of fishing. Despite some disadvantages, it has advantages. Here they are:

The lower, loading cord, when completely lowered to the bottom, rarely clings to snags and stones.
The weakened top of the net is not used, so it will not miss big fish.
A floating fish net does not get twisted even by strong swaying, and debris on the surface of the water area does not linger in it.

For the convenience of planting a network, you can make a kind of measuring stick called a “milestone”. This is a ruler or pattern for uniform planting in the form of a meter long bar with a section of 5x25.

You will be able to more accurately tie a cord or twine along the notches. In this case, the grid cells can be given one of the following shapes:

symmetrical with a width equal to the gap between its nodes;
wide, at a greater distance;
narrow - with less.

Node for attaching a net. Knitting nets. A practical guide for anglers

Fishing knots Knot for landing a fishing net

We present to your attention a video on the topic: “knots for attaching fishing nets to cords.” There is something new and educational for every fishing enthusiast. This video may well become a source of interesting solutions in matters of fishing and everything connected with it.

Interesting

Links on the topic “knots for attaching fishing nets to cords”

Methods for making connections and knots for landing a fishing net. The network fabric can be attached to the cord in several ways and using different knots. There is a small knot here that makes it easier to separate old network cords from the torn network that needs repair. If you cut this knot with scissors, the knot will fall apart. Do not use a thick thread for the safety loop, as the net fabric may get caught in the knot during fishing. https://www.float.ru/fishing-tackles/Pocadka_ribolovnoy_ceti_4.htm
The shape of the cell and its calculation when planting a fishing net. When planting a network from a ready-made network fabric, you can give different shapes to the cells of the network fabric. A cell is called symmetrical (C) if its width is equal to the distance between the nodes. Methods of making connections and nodes for landing a fishing net. The network fabric can be attached to the cord in several ways and using various nodes. The usual method of “linear” planting is shown below. https://www.mtex.net.ua/info/posadka-ribolovnoi-seti-285.html
Knots for knitting jigs. Knots for landing fishing nets. Video on how to tie fisherman's knots. A knot called a pig's hoof is made with a safety loop at the back. To do this, thread the cord under the edge of the fishing nets and then pass it over the cord behind the base of the net so that a loop is formed around the edge of the net. https://tutryba.ru/snasti/leska/rybolovnye-uzly.html
The greater the distance between nodes in the network, the longer the landing and selection will be. When planting a fishing net, the mesh cells can be given different shapes. A cell is called symmetrical if its width is equal to the distance between the nodes. The most convenient pole size is 5 x 25 x 1000 mm. At both ends of the pole, notches are made, on which the distances between the nodes are marked and applied to the power cord (so that the pole can be used for planting different networks, a removable one is glued to it... https://karasnedremi.com/posadka-rybolovnoy-seti/
The size of the “thread” is determined by the size of the mesh, which, in turn, is determined by the distance “from node to node.” For example, from a mesh fabric with the dimensions indicated on the tag - 3 m high and 120 m long, the result will be a finished net with a length of 120 x 0.5 = 60 m, and the height of such a net will not be 2.6 m. This tradition has been preserved since the times when the height of nets indicated in the number and size of cells. Dimensions of flints for trapezoidal landing of nets with a height of 1.5 - 1.*** m. Finnish type of landing of fishing nets when using the following cord lengths https://Kitaiki.ru/stati-po-rybolovnoy-tematike/set-rybolovnaja-svoimi- rukami/
Planting a net for the PanRybolov website. bombey vrn. SubscribeSubscribedCancel subscription.How to make a suspension without sinking knots in a fishing net. — Duration: 2:55 Fishing nets 5,571 views. https://www.youtube.com/watch?v=KrAFz0K95HQ
Planting of a fishing net can be carried out: – automatically (with machine knitting of the net); – manually (using a shuttle). Methods for planting a network. Using a milestone. This is one of the most popular methods. Planting “in a knot”. This is the simplest type of landing for large mesh fishing nets. However, the toughest and most reliable. The method involves threading a cord through the cells. https://www.ruboman.ru/2013/12/10/osnovnye-sposoby-posadki-rybolovnoj-seti.html
The greater the distance between nodes in the network, the longer the landing and selection will be. When planting a fishing net, the mesh cells can be given different shapes. A cell is called symmetrical if its width is equal to the distance between the nodes. The most convenient pole size is 5 x 25 x 1000 mm. At both ends of the pole, notches are made, on which the distances between the nodes are marked and applied to the power cord (so that the pole can be used for planting different networks, a removable one is glued to it... https://www.k-lev.com/content_page_2.html
Tip 1: How to plant a fishing net. It would seem that it couldn’t be easier, throw the net into the pond and after a couple of hours you will take out a plentiful catch. But not everything is so simple. The simplest installation for networks with large cells is to thread the cord through the cells. A mandatory element of landing is a knot. From the variety of knots, choose a double knot; it is very popular among fishermen and is especially often used when landing a seine. https://www.KakProsto.ru/kak-44345-kak-posadit-rybolovnuyu-set
Planting a fishing net. Page: 2/2 Directly planting the mesh fabric comes down to the following: meshes are attached to the stretched upper and lower selections at certain distances. Having found the first mesh of the lower part of the fabric, it is firmly fixed, then the required number of meshes is drawn onto the garter thread, pressed with the index finger to the first mark on the pole and knit a landing knot. In this case, it is important that the length of the garter thread (see Fig. 14) is greater than the length of the cord between the knots, or flint, as they call it... https://www.k-lev.com/content_page_2_2.html

☸ Installation methods

For fishing to be successful, it is important to correctly install the cellular gear. The easiest way to do this is from any convenient watercraft (inflatable boat, speedboat)

Other casting methods can be distinguished: the drag method, wading, swimming, figured and self-installation.

The pulling method is carried out without entering or swimming into the water. This method of installing the canvas is suitable for small reservoirs, narrow rivers, bays and bays.

You can install the net by swimming in the warm season. Some fishermen are not afraid of cold water and already in April swim along the river with their nets. This method is very risky and dangerous, because there is a high risk of getting confused yourself.

You can wade the tackle on a small body of water during spring fishing in shallow water and in places where a boat cannot pass.

The figured setup is appropriate for catching shy and cautious fish. A certain figure is formed from several networks, for example, a snake, similar to a labyrinth

This method is suitable for industrial fishing.

Casting on your own is not the most effective method. The lower and upper cords can get tangled, which is why the tackle cannot straighten out in the water column. In addition, there will be a strong splash on the water, scaring away the fish. The catch in this case will be scanty.

The most common and most convenient way to place and check nets is to swim in a boat with a partner. One person carefully rows the oars, and the second sets the net, checks it, or assembles it. It should be taken into account that in the spring navigation is prohibited in almost all regions. Therefore, before going to a particular body of water, you should ask whether it is possible to go there on a boat.

Chinese networks

These cheap nets are widely popular among fishermen. They are really knitted in China, which cannot be said about Finnish networks, which are not always made in Finland. The cheapness of Chinese nets allows you to simply leave them if they get caught, and if they get damaged, you can throw them away without regretting it at all. They come in different lengths, sometimes allowing you to cover a large part of the reservoir. At the same time, they are not of good quality, since the Chinese save on everything. Questions arise very often. The Chinese can save on sinkers, and such a net is not able to submerge in water. Very often they use low-quality knots (simple ones), which can come undone during fishing. Knowing this, many fishermen, when buying Chinese nets, correct them, eliminating defects, after which they can be used for fishing. The Chinese use regular white fishing line to weave their nets.

Knitting a casting net with your own hands

Watch this video on YouTube

It is not at all difficult to make such a network yourself. The main thing here is that there is a desire and need for it

It is very important at this stage to determine that the casting net is suitable for the existing fishing conditions. It is very important that there are enough fish in the pond

But first you need to prepare all the ingredients for its manufacture.

What is needed for this?

Naturally, to make such gear you will need a mesh fabric. In this case, there are 2 options for purchasing it.
You can knit the mesh fabric yourself, but this will take a lot of time. Among other things, you need to master the technique of knitting nets. This option has one, but significant advantage. The knitting technique will allow you to obtain a solid mesh, which can significantly affect the effectiveness of fishing.
There is another option, which is based on purchasing a ready-made network. The only problem is that the mesh fabrics are sold in strips of varying lengths and widths. The only task is to acquire a network of suitable sizes, with the appropriate cell size, which is not always possible.
You should very carefully determine the size of the mesh fabric in order to make the tackle of the right size. Since casting nets are round in shape, their size does not refer to the diameter of the net, but to the length of its circumference. As a rule, the diameter of the tackle is equal to two sizes of the mesh in width. Therefore, the size can be calculated based on the following formula.
Network size = 2x3.14 x network width.
Approximately this amount of mesh fabric needs to be cut along its length.
The second, no less important part of the design is a braided cord, the thickness of which can correspond to 4 mm. This is the so-called cargo cord, which is located along the perimeter of the future gear. Its length is selected depending on the size of the network. You can determine the size of the load cord after laying out the prepared network segments. Weights are usually attached to this cord.
You also need a braided cord, 7-8 mm thick, to throw the net into the water, and its length should be about 7 meters. Although it makes sense to use a shorter cord to start with. After the application technique has been mastered, it makes sense to increase the length of the cord. The further the casting net is thrown, the greater the chances of catching fish. Be that as it may, the fish may be frightened by a net falling into the water. At the same time, the cord should not be too thin, as it will cut your hands when casting.
Set of weights. The weight of each load is selected within 20-30 grams. Weights are attached around the entire circumference, at a distance of about 10 cm from one another. It is not difficult to calculate that a lot of them are needed - up to 250 pieces. Therefore, it is not difficult to calculate how much the finished network will weigh. You can make weights yourself.
You will need a center ring. The design assumes that lines will be output through this ring, which will then go into a mount connecting them to the casting cord.
You need up to 150 meters of fishing line, up to 1 mm thick, from which slings should be made. The slings are connected at one end to the load cord, and at the other end to the throwing cord.
You need a DRAGON HEAD device to connect all the lines at the point where they are connected to the main cord. Although you can do without such a device by tying all the slings and cord with a secure knot. For greater reliability, the assembly is impregnated with epoxy glue.
You will also need lavsan threads (up to 100 meters) to attach the cargo cord to the base of the net. Alternatively, you can use a similar fishing line.
Fishing line, up to 0.4 mm thick, for fastening parts of the mesh into one whole.

Where and how to use the grid correctly

Of course, it’s no secret that float mesh is most often used for catching fish, but let’s look at some more points where it can be used:

Quite often, a floating net is used to catch running fish, which at a certain time moves up the water and sometimes covers long distances. This method is often used for fishing for omul, salmon, sterlet, and ide;
approach the place responsibly, since the chosen river must be without flaws, without twists, bends, there should be no current and there should be no other banks nearby;
if you plan to fish on the bottom, then you need to avoid places with poor terrain, without driftwood, or ledges. The pond must be clean so that you do not break your nets;
riding gear is used to catch fish in the upper part of the water;
bottom tackle is used only for fishing at the bottom of a reservoir, the cord that is used ensures its immersion;
the soil must be selected from sand or one that will be covered with silt, since small shells or pebbles can become the main threat to the rapid wear of your fishing gear.

Finally, it is worth mentioning one more net, which, although not intended for direct fishing, is an indispensable assistant for carp fishermen. This is a PVA net for fishing, the peculiarity of which is the ability to dissolve in water.

It is made from polyvinyl acetate (abbreviated PVA).

Solid.
Cellular.
Floating.
Drowning.

Floating baits are delivered to the site through the water column; this method can be effective when fishing for carp. Sinkers, as the name suggests, dissolve at the bottom, forming a tasty pile of food at the bottom. Solid ones have the appearance and shape of a bag, but do not dissolve very quickly.

Using a PVA net for fishing, you can quickly and accurately deliver bait to the fishing site, which is very important for this type of fishing, such as carp fishing. This fishing net is the only one that cannot be considered poaching gear

All the rest are classified as prohibited gear and the net can only be used if the fisherman has a commercial fishing license

This fishing net is the only one that cannot be considered poaching gear. All the rest are classified as prohibited gear and the net can only be used if the fisherman has a commercial fishing license.

It is also necessary to remember that nets that have not been removed or forgotten in a reservoir create a lot of problems for both the inhabitants of the reservoir and the fishermen.

DIY fishing net planting

The cells can be made in different shapes - symmetrical, wide or narrow.

One of the most important stages in the manufacture of a fishing net is equipping the net fabric, or rather, placing it on floating and weighted pick-ups. Planting can be done manually using fishing shuttles or by machine.

Often the bottom line is made 20 percent longer than the top line to provide slack, which increases the catchability of the net and protects it from skewing. The upper part of the net is rarely made longer than the lower one; this is mainly used for drift nets and also has a number of advantages: the upper part of the net becomes more catchable due to the weakening of the tension and the net breaks less. In this case, the weighting cord does not catch on branches and stones, does not twist, and the net itself does not catch debris and holds large prey well. In order to plant the net on selections of different lengths, it is necessary to plant fabric cells with a smaller distance between the nodes on a cord that should be shorter.

As a rule, for fixed nets, the upper and lower pick-ups are made the same in length - this ensures ease of installation and easier pulling of the net. This is how all standard networks are planted, including Chameleon Standart.

When planting a net, the cells can be made of different shapes - symmetrical, wide or narrow, this depends on the type of fish being caught and is regulated by the landing coefficient. The landing coefficient is determined by the shape of the cell and has a numerical designation. The length of the finished network can be determined by multiplying the length of the mesh by the landing factor. The value of the landing coefficient is usually set initially in order to obtain the desired rhombus shape: if it is necessary to completely extend the cell in length, then a coefficient of 1 is set, in which case the cell will have no height.

For smooth networks, it is recommended to use a landing factor from 0.6 to 0.67. For medium-sized fish, it is better to use a coefficient from 0.35 to 0.45, for taller ones - from 0.3 to 0.4, and for more rounded ones - from 0.5 to 0.67. Recommended landing coefficients for catching various types of fish: bream - 0.33; vendace – 0.5-0.6; salmon – 0.5-0.65; flounder 0.65-0.75; the universal network is usually planted with a coefficient of 0.5. A net with this landing coefficient can be used to catch almost any type of fish.

At the beginning of planting, you can tie the first 5-10 cells in advance to the cord you have chosen, and the first two cells in general to one place to increase strength and in order to set the desired angles of the finished network. Often, for correct fit, stakes are used (a ruler with marks on it to measure the exact distance between the nodes), which are applied to the cord to determine where the selections are attached to the mesh fabric.

Typically, the fabric is placed on the pick-ups while sitting, and the pick-up cord must be tensioned to increase the strength of the knots. A large-mesh mesh can be planted by first attaching a rope or cord to the outer cells, for which you need to separate the cells with your hands and thread the rope inside.

Selection of cargo for the bottom net

For bottom nets, the weighting capacity, on the contrary, should be 1.2 – 1.5 times greater, depending on the strength of the current in the reservoir. For reservoirs with weak currents, a floodability margin of 1.2 times is sufficient. Similar to the floating net, we calculate the weight capacity (3200g x 1.2 = 3840g) and then the total weight of the sinkers (3840g / 0.91 = 4220g). The weight of one sinker in our example is 100 g. Under these fishing conditions, to equip the bottom net, we will use 42 pieces of 100 g sinkers located at a distance of 1.22 m.

Please note that this article provides only recommended calculation indicators. In each specific case, they may vary depending on fishing conditions and the characteristics of the network.

On our website you will find everything you need to make fishing gear: these are the nets and parts themselves, floats, sinkers, needles, cords, threads and ready-made selections. We send orders to all regions of the country using a variety of services, including the usual postal service, cash on delivery. You can familiarize yourself with the options, timing and approximate cost of delivery by going through the delivery methods.

Material taken from the magazine “Fishing and Fish Farming”.

Independent planting of nets and choice of mesh fabric

To plant networks yourself, in the absence of experience, you need to consult a specialist or read the literature and relevant materials on the Internet. It is necessary to make preliminary calculations on the mesh size and the shrinkage coefficient of the canvas. This will allow you to correctly determine the selection length.

Then the necessary network materials are purchased. For beginners in this business, it is better not to mess with sinkers and floats. A floating and weight cord is the right solution to the problem. The mesh should also be taken simpler, for example, from monofilament. It is much easier to work with a net made of thick fishing line when planting nets.

Fishing nets made in China have a straight sliding fit. The cells of the fabric are simply put on for selections. Such a network is not suitable for repair. This is a one-time item.

Real nets are mounted on an intermediate nylon thread (string), with a diameter of 0.3-0.7 mm. At certain intervals - flint, this planting thread is attached to the selections using special knots made with a shuttle or a “needle”. The length of the flint depends on the mesh size and the network landing coefficient.

There are various ways to plant nets on flint. Most often, there are 4-5 cells per flint. The length of the flint is determined by a simple calculation. Let’s say the fabric has a mesh of 30 mm, fit 1:2. One flint contains, for example, 4 cells. We multiply 30 mm by 2 (mentally stretch the network into a line) and multiply by 4 again. We get 240 mm. If the planting is carried out 1:2, then the length of the flint will be 120 mm. Usually they strive to make the flint length close to 200 mm. This means that for a 30 mm cell, you can put 6 cells on one flint. Then for a 1:2 landing, the length of one span or flint will be 180 mm - the approximate length of the shuttle. They measure out where to tie the next flint with the collected cells to the selection.

https://www.k-lev.com/content_page_2.htmlhttps://petrokanat.shop/stati/pravila-posadki-rybolovnyh-setej/https://ribaku.info/snasti/spinning/posadka-rybolovnyh-setejhttps: //tvoyulov.ru/news/posadka-seteyhttps://dopul.ru/snaryazhenie-i-transport-rybaka/454-glavnye-metody-posadki-rybackoj-seti.htmlhttps://tvoyulov.ru/news/posadka- setey

Network device. Upper and lower selection

Any simple single-wall network consists of several elements:

Mesh fabric (del, doll) is a machine-knitted product made in the form of uniform rows of cells of the same size - cells. The fabric is made from nylon threads ( nylon mesh fabrics ), monofilament and curly fishing line ( filament mesh fabrics ). To turn the fabric into a full-fledged fishing net, the mesh fabric must be placed on the upper and lower thicker cord (selection), and not in a stretched state, but in a free, seated state (in a ratio of 1:2, less often 1:3). Therefore, the planted network looks like a lot of diamonds, not squares.
The top pick is made from durable netting cord called a net. It serves to secure the net and has hard foam floats (floats). a floating cord is more often used for the top selection . This makes the work of setting up networks and unraveling them much easier.
The lower selection also serves to secure the mesh fabric and secure sinkers (steel rings, lead). Recently, instead of individual sinkers, a weight cord .

A network of several walls differs from a simple network by the presence of an additional mesh fabric (one or two) with a very large mesh, on average 150-200 mm. Such fabrics are called “ryazh” and serve to form bags from a seated main fabric with a small mesh, which themselves are formed when large fish enter.

Frame networks are ordinary single-wall networks, which are additionally shrinked in height by 20%. This is achieved using vertical veins of thicker thread or fishing line. In addition, frame networks can also have horizontal veins, which also shrink the fabric a little. As a result, a very catchable system of rectangular pockets is formed in the network, which act as bags in a multi-walled network.

The choice of cargo and floating cord depends on the material and mesh size of the mesh. Floating nets are used to catch some species of riding fish. Therefore, the weight of the sinkers or cargo cord, together with the weight of the netting and the cords themselves, should be less than the displacement of the floats or floating cord. For most sinking nets the situation is reversed. The weight of the equipped net must be greater than the carrying capacity of the floating cord or floats. The net should sink slowly, so the difference in weight should not be more than 20%.

The selection of floats and sinkers for fishing in various conditions also follows the principles that are set out for the selection of weights and floating lines.

Rafting nets are widely used on large rivers. They have stronger rebounds, heavier weights and lifting floats. In the lower reaches of Siberian rivers, the main fishing for all types of whitefish is carried out with sinking rafting nets. Their strength is such that with a bottom hook, the net holds a large motor boat in a strong current. Naturally, the upper bridle, which goes to the boat, must be passed through the bow bollard.

Planting mesh fabric on cords – Cottage, garden, vegetable garden, indoor plants

Planting fishing nets with your own hands is a long process compared to the machine method. But this type of gear is more catchy and softer to work with.

Features of equipping a fishing net - correct fit and choice of net materials

: 02.07.2016 12:25

In a broad sense, the word “nets” means fishing gear of various designs and purposes. They can be divided into two large groups:

Fishing gear that strains fish are seines, dragnets, trawls and other tools that, as a rule, have thick, durable, but small-sized cells.
Fishing gear that ties fish by the gills are fixed nets of various designs, floating nets and a number of other gear.

Let's look at the usual, most common gill fishing nets for recreational fishing, which is carried out under licenses. Such networks are also divided into several categories:

• fixed nets (single-wall, double-wall and three-wall, frame nets) – these are lightweight nets that are used in low currents, on lakes, ponds and reservoirs;

• floating nets with different numbers of walls - heavier nets that are used in the current; thanks to a special float-cross (loon), the nets drift with the current along with the boat.

Nowadays no one knits mesh fabric with their own hands, as it was half a century ago. At that time, there were almost completely homemade copyright networks, which were passed down from father to son, they were looked after, they were constantly repaired during the long winters.

A lot of fish are dying. The very concept of net fishing is being discredited.

Network device. Upper and lower selection

Any simple single-wall network consists of several elements:

Mesh fabric (del, doll) is a machine-knitted product made in the form of uniform rows of cells of the same size - cells. The fabric is made from nylon threads (nylon mesh), from monofilament and curly fishing line (filament mesh). To turn the fabric into a full-fledged fishing net, the mesh fabric must be placed on the upper and lower thicker cord (selection), and not in a stretched state, but in a free, seated state (in a ratio of 1:2, less often 1:3). Therefore, the planted network looks like a lot of diamonds, not squares.
The top pick is made from durable netting cord called a net. It serves to secure the net and has hard foam floats (floats). Nowadays, a floating cord is more often used for top bridging. This makes the work of setting up networks and unraveling them much easier.
The lower selection also serves to secure the mesh fabric and secure weights (steel rings, lead). Recently, instead of individual weights, a weight cord has been used.

Frame networks are ordinary single-wall networks, which are additionally shrinked in height by 20%. This is achieved using vertical veins of thicker thread or fishing line.

In addition, frame networks can also have horizontal veins, which also shrink the fabric a little.

The choice of cargo and floating cord depends on the material and mesh size of the mesh. Floating nets are used to catch some species of riding fish.

Therefore, the weight of the sinkers or cargo cord, together with the weight of the netting and the cords themselves, should be less than the displacement of the floats or floating cord. For most sinking nets the situation is reversed.

Network device. Upper and lower selection

Any simple single-wall network consists of several elements:

Mesh fabric (del, doll) is a machine-knitted product made in the form of uniform rows of cells of the same size - cells. The fabric is made from nylon threads ( nylon mesh fabrics ), monofilament and curly fishing line ( filament mesh fabrics ). To turn the fabric into a full-fledged fishing net, the mesh fabric must be placed on the upper and lower thicker cord (selection), and not in a stretched state, but in a free, seated state (in a ratio of 1:2, less often 1:3). Therefore, the planted network looks like a lot of diamonds, not squares.
The top pick is made from durable netting cord called a net. It serves to secure the net and has hard foam floats (floats). a floating cord is more often used for the top selection . This makes the work of setting up networks and unraveling them much easier.
The lower selection also serves to secure the mesh fabric and secure sinkers (steel rings, lead). Recently, instead of individual sinkers, a weight cord .

The selection of floats and sinkers for fishing in various conditions also follows the principles that are set out for the selection of weights and floating lines.